1 Wine Cellar Cooling Systems Through-the-Wall Wine Cellar Cooling Systems Installation, Operation and
10 Standard Specifications The Wine Guardian System Contains A capillary tube expansion to control the flow of refrigeration into the evaporat
11 Accessories and Optional Equipment Installation Sleeve Each Wine Guardian system includes an EasyMount™ installation sleeve to be used
12 Overview of the Wine Guardian Unit Refer to illustrations on page 10 Cabinet – The cabinet is constructed of aluminum with a powder coate
13 Overview
14 TTW 018
15 TTW009
16 Safety The following is suggested before installing or maintaining the Wine Guardian System: 1) Read these instructions 2) Keep these instructions
17 Lockout/Tagout Procedure 1) Turn the system to off at the local interface controller (the display will indicate the system is off). 2) Unp
18 Moving Parts Hazards The Motor and Blower must be disconnected prior to opening access panels. The motor can start automatically. Disconnect all
19 Always operate this equipment from a 120Vac, 1 phase 60Hz power sources only. Always ground the outlet to provide adequate protections against v
2 TABLE OF CONTENTS Introduction ... 4 Wine Guardian’s
20 Installation CAUTION SHARP EDGES RISK OF SERIOUS INJURY Sharp edges are present inside the Wine Guardian system. Pre-installation
21 WARNING RISK OF PERSONAL INJURY OR DAMAGE TO EQUIPMENT Modification to the equipment may cause in
22 Where to locate the unit? It can be mounted flush with the racking or flush with the wall on the wine cellar side. How to mount the unit? A m
23 You must then move the red voltage switch in the opposite direction as from the factory to move the internal power from the condenser side to the
24 Step 3 Slide the EasyMount™ sleeve through the wall penetration so that the flanged area of the sleeve sits flush with the surface of the wall. En
25 Installing the Condensate Overflow Condensate generation is a natural by-product of air conditioning systems. The Wine Guardian cooling coils are
26 Wiring the System for Power WARNING ELECTRICAL SHOCK HAZARD The electrical outlet and wiring installation must meet the national and local buildi
27 Installing the Thermostat and Communication Cable The Wine Guardian Local Interface Controller is a combination temperature and humidity control
28 2. Remove the back plate of the controller and mark the mounting points at the desired location. (F
29 Installation of the Optional Wine Guardian Remote Sensor The Remote Sensor is a combination temperature and humidity sensor only. It is designe
3 Installing the Condensate Overflow ... 25 Installing the Drain Line ...
30 4. Drill two 1/8” holes and insert anchors (provided) within the mounting surface. Anchors may not be require
31 Joining Communication Cable Changing Jumper Positions (Averaging readings from Remote Sensor) If using multi
32 Standard Controller Functions How to: Turn system on/off Press the On/Off” button once. NOTE: There is a five- second t
33 Deg F or Deg C Setting 1 Press the “Down” arrow to change temperature from Deg F to Deg C. Press the “Up” arrow to change temperatur
34 Advanced Settings- Special access required. Contact Wine Guardian Service Department for access code Setting 8 Press “Mode” button to advanc
35 Differential temperature adjustment Setting 16 Press “Mode” button to advance to Setting 16. Press the “Up” or “Down” buttons to adjust
36 Alarm Codes High temperature alarm Press the “Up” or “Down” arrow once to change screen from alarm to normal Temperature and Humidity indicatio
37 Starting-up and Operating the Wine Guardian Control Settings The control has been wired and set up in the factory for testing with default setti
38 Regulating the Wine Cellar Temperature To keep the entire wine cellar at the same temperature, set the thermostat to run the supply fan continuous
39 CAUTION EXPOSURE TO MICROBIAL GROWTH (MOLD) CAN CAUSE SERIOUS HEALTH PROBLEMS Standing water in drain pans promote microbial growth (mold) that c
4 Introduction Dear Customer, Congratulations and thank you for purchasing a Wine Guardian cooling system. We believe it to be the best wine cellar
40 High Pressure Switch has Shut the System Down Every Wine Guardian system has a manual reset high pressure switch in the refrigeration system. This
41 Troubleshooting WARNING BEFORE PROCEEDING, READ AND UNDERSTAND THE SAFETY INFORMATION CONTAINED IN THE SAFETY SECTION OF THE WINE GUARDIAN MANUA
42 Unit is Operating and Blows Evaporator Air, but the Supply Air is not Colder than the Return Air from the Cellar Possible Cause Solution Thermost
43 Problems Controlling Cellar Humidity Humidity too low or supply air is too cold, without optional Standalone humidifier Possible Cause Solution
44 Humidity too high when unit is not running Possible Cause Solution System needs to run to dehumidify Lower room temperature setpoint. Seal ope
45 Warranty GENERAL Wine Guardian warrants, to the original buyer, its goods and all parts thereof to be free from defects in material and work
46 Through-the-Wall Return Policy TTW Warranty term Wine Guardian warrants, to the original buyer, its goods and all parts thereof to be free from
47 Out of Warranty Should a problem develop with the Wine Guardian unit out of warranty you can contact Air Innovations Service Department for a quot
5 Directory of Terms Ambient Air – The surrounding area outside the cellar such as a room, basement, garage or outdoors. CFM – Cubic feet per minute.
6 Receiving, Inspecting and Unpacking the Wine Guardian System NOTE: Wine Guardian systems are factory assembled and tested prior to shipment. Wine
7 General Description The Through-the-Wall Wine Guardian cooling system is a professional grade, self-contained climate control system desi
8 Wine Guardian Controls Wine Guardian’s digital electronic control series offers a versatile solution for controlling and monitoring your win
9 Wine Guardian Controls Main Control: Performs all switching functions and interfaces with inputs and o
Comments to this Manuals